Model-specific code library

Frigidaire dishwasher error codes.

The i-code and E-code dishwasher manuals carry the same meanings row for row, with a different prefix. The newest manual we hold has no table at all, so older tables apply to older units.

Dishwasher code finder

i20 means clogged filters or a restricted drain line were detected, and Frigidaire's article adds that the unit didn't drain completely. Clean both filters and the sump, check the drain hose, then reset the dishwasher.

Read the i20 checks
Or choose

11 researched dishwasher codes. Codes differ from model to model; your manual has the final word.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Messages with a manual behind them.

01-24

Mode, not a failure

01-24 on a Frigidaire dishwasher is not an error. Frigidaire's article says the Delay option is on, and the cycle begins when the displayed time reaches 0. To cancel the delay, press or hold Cancel.

No action needed
CL

Door

CL, also shown as Cd, means the dishwasher door hasn't been closed and latched. Close it fully and the code clears. If you can't get the door to close, contact service to check it.

Owner checks first
HO

Heat delay

HO, also shown as Hd, means the dishwasher is in Heat Delay or Heater On mode. It's the unit warming the water, and the sources list no steps. Colder incoming water means a longer delay.

No action needed
i10

Water supply

i10 means the dishwasher detected a low fill. Check that the water supply line isn't pinched and that the shutoff valve is fully open, then reset the dishwasher. If i10 stays, book a technician.

Owner checks first
i20

Drain

i20 means clogged filters or a restricted drain line were detected, and Frigidaire's article adds that the unit didn't drain completely. Clean both filters and the sump, check the drain hose, then reset the dishwasher.

Owner checks first
i30

Leak

i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.

Owner checks first
i40

Drain

i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.

Owner checks first
i50

Motor

i50 means a problem has been detected with the drain or wash motor. The manual says to press Cancel or switch off at the breaker for 5 minutes, which should clear the code so you can restart. If i50 returns, book a technician.

Owner checks first
i60

Heating

i60 means a problem has been detected with the water heating system. The manual gives one owner step, the reset: Cancel, or power off at the breaker for 5 minutes. If i60 stays, service will be needed.

Owner checks first
iC0

Electronics

iC0 means a problem has been detected with the electronic control system. The manual's only owner step is the reset: Cancel, or power off at the breaker for 5 minutes. If iC0 returns, book a technician.

Owner checks first
PF

Power

PF means the dishwasher lost power. Press START/CANCEL to clear the code and begin a new cycle. After a hard power failure, the 2020 guide says pressing Start within 18 hours can resume the cycle where it stopped.

Owner checks first

Start with the model boundary.

Open dishwasher with empty racks between walnut kitchen cabinets

Two tables, the same meanings.

The i-code and E-code dishwasher manuals carry the same meanings row for row, with a different prefix. The newest manual we hold has no table at all, so older tables apply to older units.

One manual prints iC0 and the other EC0, which breaks the usual pattern, and the reset step differs: 5 minutes in a manual, 3 minutes in an article. ER, UO and UF appear in neither table nor any article.

Choose the next safe action.

Read the whole display

Read the exact characters on the display, and check whether it shows i or E. Note the date on the manual that came with the unit.

Respect the service boundary

Water that keeps entering, or any leak, means turn off the supply and book a visit. Wiring and the pump stay with the technician.

Documents checked for this library.

  • Dishwasher Use & Care, A117867311
  • User Manual, Dishwasher, 117825980A
  • Dishwasher Use & Care, A23587501B
  • Dishwasher Error Codes and Alarms Guide (KB 1829620)
  • Dishwasher message code (KB 1852991)

Follow the instructions written for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are these dishwasher meanings universal?

One manual prints iC0 and the other EC0, which breaks the usual pattern, and the reset step differs: 5 minutes in a manual, 3 minutes in an article. ER, UO and UF appear in neither table nor any article.

Which details help when I report a code from my dishwasher?

Take a photo of the whole dishwasher display and of the model label. Add what the appliance was doing at the time, and skip explanations written for other appliances.

Why do some dishwasher codes have no meaning listed?

An old search phrase is not proof of what a code means. When our dishwasher sources do not explain a message, we keep its name as written and point you to help, without naming a part or a cause.

How do I know which dishwasher models a code applies to?

Open the dishwasher documents in this library and check the models listed on their covers against your label. A different model calls for its own instructions.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.