What it means
i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.
Frigidaire dishwasher i40 / Drain
i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.
Also shown as i40
i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.
Remove and clean the glass trap and the filter, which Frigidaire's i40 article gives as the fix, then run the dishwasher again.
i40 continues after the filters, the sump and the hose have been cleaned and checked.
Your checklist / kept on this device

Remove and clean the glass trap and the filter, which Frigidaire's i40 article gives as the fix, then run the dishwasher again.

The manual's row says to check and clean both filters and the sump area.

Look for a pinched or blocked drain hose, which the same manual row lists.

If the code carries on, Frigidaire's guide says to arrange service.
Tell us the model and what you have already checked, and start the request right here.
Book a visit
Simplified schematic; real layouts differ by model. Tap an outlined part for its photo and the check that goes with it.

Component reference
The filter system at the bottom of the dishwasher tub catches food soil so it doesn’t clog the drain.
Read the definitionFrigidaire's article names both and says to clean them. The manual row calls them both filters and the sump area.
Read the supporting manualNot always. The guide says to arrange service if the code continues.
Read the supporting manualManufacturer document
Frigidaire / Electrolux
September 2020 / PDF p.9 (Error Code table)
Manufacturer document
Frigidaire / Owner Center knowledge base
Owner Center article, cached 10.11.2026 (no edition date printed) / Article text
Manufacturer document
Frigidaire / Owner Center knowledge base
Owner Center article, cached 10.11.2026 (no edition date printed) / Article text
Manufacturer document
Frigidaire / Electrolux
No date printed / PDF p.10, section 4.5 Error Codes
This code is from the i-code table in the 2020 Use & Care guide. The newer dishwasher manual prints the same table with an E prefix, so read the row in the manual that came with your dishwasher. In that table i40 shares a row with i20 and iF0; the newer manual prints it as E40.
The article says food soils have built up in the sump. The sources name no other cause.
They share a row in the code table. Frigidaire's separate articles describe i40 as a clogged filter or sump and i20 as not draining completely.
The i40 article gives cleaning and a re-run, with no reset. The footnote for all codes does give the Cancel or breaker reset.
Frigidaire's guide says to arrange service if the code continues after cleaning.
Code / problem / part / repair
i20 means clogged filters or a restricted drain line were detected, and Frigidaire's article adds that the unit didn't drain completely. Clean both filters and the sump, check the drain hose, then reset the dishwasher.
Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.
The filter system at the bottom of the dishwasher tub catches food soil so it doesn’t clog the drain. Frigidaire’s guide covers a coarse filter and a cylinder fine filter, which also catches glass, bones and pits. A clogged one is behind i20 and i40, poor cleaning and slow draining.
Book a diagnostic for your model, done at your home.
Office addresses and the entry details to have ready.