Frigidaire dishwasher iC0 / Electronics

Frigidaire dishwasher
error iC0

Dishwasher / display referenceiC0

iC0 means a problem has been detected with the electronic control system. The manual's only owner step is the reset: Cancel, or power off at the breaker for 5 minutes. If iC0 returns, book a technician.

Also shown as iC0

Last reviewed

Dishwasher / display referenceiC0
Meaning
iC0 means a problem has been detected with the electronic control system. The manual's only owner step is the reset: Cancel, or power off at the breaker for 5 minutes. If iC0 returns, book a technician.
Who handles it
Owner checks first, then a technician
Related codes
Source
Dishwasher Use & Care, A117867311

What Frigidaire dishwasher iC0 means.

What it means

iC0 means a problem has been detected with the electronic control system. The manual's only owner step is the reset: Cancel, or power off at the breaker for 5 minutes. If iC0 returns, book a technician.

What you can safely check

Press Cancel, or switch the dishwasher off at the breaker and leave it off for 5 minutes.

When to call a technician

iC0 comes back after the reset.

Your checklist / kept on this device

Safe checks, in order.

0 of 3 checks done
  1. Frigidaire dishwasher iC0: Row of small touch buttons and one glowing light along the top edge of a stainless dishwasher door, seen at a low angle.
    Illustration. Follow your model’s instructions.
    Before you begin

    Reset the dishwasher

    Press Cancel, or switch the dishwasher off at the breaker and leave it off for 5 minutes. The manual gives this as the step for every error code.

  2. Open dishwasher tub with the lower rack removed and a shallow pool of water around the cylindrical filter.
    Illustration. Follow your model’s instructions.
    Check 2

    Run it again

    Start a cycle and see whether iC0 shows again.

  3. Hand lifting a gray dishwasher spray arm above its hub in an empty tub with the lower rack removed
    Illustration. Follow your model’s instructions.
    Check 3

    Book a technician if it returns

    The manual lists no other owner steps and points to service.

Still showing iC0?

Tell us the model and what you have already checked, and start the request right here.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 2Control board
  2. 3Motor wiring
  3. 4Heater wiring

Simplified schematic; real layouts differ by model. Tap an outlined part for its photo and the check that goes with it.

A little more context.

Is iC0 the same as EC0?

The newer manual lists the control-system row as EC0, while the 2020 guide prints iC0. Each is read from its own document.

Read the supporting manual

The manual behind the message.

Manufacturer document

Dishwasher Use & Care, A117867311

Frigidaire / Electrolux

September 2020 / PDF p.9 (Error Code table)

Manufacturer document

User Manual, Dishwasher, 117825980A

Frigidaire / Electrolux

No date printed / PDF p.10, section 4.5 Error Codes

This code is from the i-code table in the 2020 Use & Care guide. The newer dishwasher manual prints the same table with an E prefix, so read the row in the manual that came with your dishwasher. The newer table prints this row as EC0, not E-C0, so the E prefix isn't a simple swap here.

Here to help

Good questions.
Clear answers.

Talk to our team
What does iC0 mean?

The manual says a problem has been detected with the electronic control system. It doesn't name a board or any other part.

Can I fix it myself?

The only owner step in the manual is the reset. Anything past that is for service.

Is EC0 the same code?

The newer manual prints this row as EC0. The two documents are separate, so check the table in the manual for your dishwasher.

Will the reset clear it for good?

The manual says it may clear the code. If it returns, it points to service.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.