Start from the symptom
Frigidaire dishwasher leaking.
Stop the dishwasher and shut off its water supply before anything else. Frigidaire’s leak article starts with the drain hose, the door and the supply connections, then asks about filters, detergent and spilled rinse aid. An i30 code means the unit sensed water in its bottom pan.

Start with safe observations.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Stop and shut the water off
Don’t run another cycle to test it. Close the supply valve only if you can get to it dry-footed, and keep away from the outlet and any wet wiring.
- 2
If it is newly installed
Frigidaire’s first questions are about installation: is the drain hose fitted as the installation guide shows, is it clear and draining, and is the door shutting fully. The kick plate can stop the door closing all the way. After a new garbage disposal, the knockout plug inside the disposal inlet has to be removed.
- 3
Check the supply hose connections
Look at where the supply hose meets the water valve. The connections should be tight and the hose should have no kinks.
- 4
Clean the filter, glass trap and spray arms
A clogged filter can cause a leak, per Frigidaire. Clean the filter, glass trap and spray arms, then run a clean cycle.
- 5
Think about suds
Dish soap or hand soap makes too many suds, and so does too much dishwasher detergent. Use the recommended amount or one tablet, and put it in the dispenser, not loose in the tub. Wipe up spilled rinse aid before the next cycle, since it foams.
- 6
Check the gasket and level
The 2025 manual adds two checks: the door gasket should sit in its channel, reach the bottom of the tub and not stick out past the end rib, and the dishwasher should be level.
Systems a technician may investigate.
These parts are linked to the problem. What you noticed does not prove any one of them has failed.

Dishwasher filter and glass trap
The filter system at the bottom of the dishwasher tub catches food soil so it doesn’t clog the drain. Frigidaire’s guide covers a coarse filter and a cylinder fine filter, which also catches glass, bones and pits. A clogged one is behind i20 and i40, poor cleaning and slow draining.

Water inlet valve
The water inlet valve opens to let supply water into the appliance, and shuts to stop it. Frigidaire’s guides name it for dishwasher codes i10 and i30, for refrigerator ice maker and dispenser water, and for washer filling. Hissing or buzzing as it opens is normal.
Read the related care guide.

Strange noise from the dishwasher? Start here.
Most dishwasher sounds are part of a normal cycle. Frigidaire's noise guide lists hissing from the water valve, humming from the wash and drain pumps, clunks from the detergent cup and ball valve, and whooshing spray arms. A knock or bang usually means something is hitting a spray arm.

Spotty glasses and damp dishes? Check the rinse aid first.
Fill the rinse aid dispenser to the indicated level without overfilling, raise the L0 to L6 setting one step if you see spots and poor drying, and keep the detergent dose matched to your water hardness.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit for any leak that continues after these checks, for an i30 code, or for water you can’t trace. If the dishwasher was installed in the last 30 days, Frigidaire’s article sends you back to the installer first. If it’s under Frigidaire’s warranty, Frigidaire handles that repair.
Arrange a diagnosticSources and model boundaries.
These documents back up the Frigidaire dishwasher leaking advice. Use the manual that matches your model.
- Dishwasher - Water Leaking (KB 1838717)
- Dishwasher Use & Care, A117867311
- Dishwasher Use & Care, A23587501B
Follow the instructions written for your own model. See how we research these pages.
What does i30 mean on a Frigidaire dishwasher?
The unit detected a leak or overflow in the bottom pan. The manual says to check the water inlet valve connections and the level, then reset it. If i30 stays, book a technician.
Can too much detergent make my dishwasher leak?
Yes. Frigidaire says too much detergent, or dish or hand soap, causes over-sudsing that can spill out. Use the recommended amount in the dispenser only, and wipe up spilled rinse aid.
Can a dirty filter cause a leak?
Frigidaire lists a clogged filter as a possible cause. Clean the filter, glass trap and spray arms, then run a clean cycle and see whether the leak returns.
Is it safe to keep using it until someone comes?
No. Keep the supply valve closed and hand-wash dishes until the leak is traced.
Code / problem / part / repair
From the code to what you do next.
i30
i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.
Frigidaire dishwasher noises
Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.
Water inlet valve
The water inlet valve opens to let supply water into the appliance, and shuts to stop it. Frigidaire’s guides name it for dishwasher codes i10 and i30, for refrigerator ice maker and dispenser water, and for washer filling. Hissing or buzzing as it opens is normal.
Dishwasher repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.