Independent appliance repair

Frigidaire dishwasher repair, with care.

We repair Frigidaire dishwashers that leak, won’t start, don’t drain or dry, or show an i or E code. Tell us the code or the flashing lights and when it stops, then book a visit.

Open dishwasher with empty racks between walnut kitchen cabinets
Independent service. Considered care.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
RefrigeratorsWall ovensDishwashersWashersDryersFreezersCooktopsRangesError code helpWarranty on our workmanship

When your dishwasher needs attention.

Symptom

Frigidaire dishwasher noises

Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.

Symptom

Frigidaire dishwasher leaking

Stop the dishwasher and shut off its water supply before anything else. Frigidaire’s leak article starts with the drain hose, the door and the supply connections, then asks about filters, detergent and spilled rinse aid. An i30 code means the unit sensed water in its bottom pan.

Symptom

Frigidaire dishwasher lights flashing

Flashing lights on a Frigidaire dishwasher have three listed meanings: a power failure, a door that isn’t closed, or a shorted keypad. The pattern tells you which, and the first two clear on their own once you act.

Symptom

Frigidaire dishwasher not drying dishes

Wet dishes aren’t always a failure. Frigidaire’s drying article points first at what is wet, the cycle and drying option you chose, rinse aid, water temperature and the drain hose. Plastic and bowls with a concave bottom often stay damp.

Symptom

Frigidaire dishwasher controls not responding

The usual reason is the child lock, which Frigidaire built to stop settings being changed. Delay Start turns it on and off, and the method depends on your tub. If the keypad is shorted, a 5-minute power-off may clear it.

Symptom

Frigidaire dishwasher detergent dispenser

If detergent is left in the cup after a cycle, something blocked the dispenser or stopped it opening. Frigidaire’s checks are dish placement around the cup, fresh detergent and a finished cycle. The cup opens by itself, so nothing should need prying.

Symptom

Frigidaire dishwasher won’t start

Work down Frigidaire’s list: power, door latched, Delay Start, any code, water supply and drain hose. A CL or Cd code means the door isn’t latched, and the dishwasher won’t run until it is. If you opened the door mid-cycle, it needs Start pressed again.

Symptom

Frigidaire dishwasher not cleaning

Start with the cycle and the loading, then the detergent, then the filter, glass trap and spray arms. Frigidaire’s cleaning article also says to run an empty cycle on the highest heat setting. An i40 code means food has built up in the filter or sump.

A message on the display?

i10Owner checks first

Water supply

i10 means the dishwasher detected a low fill. Check that the water supply line isn't pinched and that the shutoff valve is fully open, then reset the dishwasher. If i10 stays, book a technician.

i20Owner checks first

Drain

i20 means clogged filters or a restricted drain line were detected, and Frigidaire's article adds that the unit didn't drain completely. Clean both filters and the sump, check the drain hose, then reset the dishwasher.

i30Owner checks first

Leak

i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.

i40Owner checks first

Drain

i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.

i50Owner checks first

Motor

i50 means a problem has been detected with the drain or wash motor. The manual says to press Cancel or switch off at the breaker for 5 minutes, which should clear the code so you can restart. If i50 returns, book a technician.

i60Owner checks first

Heating

i60 means a problem has been detected with the water heating system. The manual gives one owner step, the reset: Cancel, or power off at the breaker for 5 minutes. If i60 stays, service will be needed.

iC0Owner checks first

Electronics

iC0 means a problem has been detected with the electronic control system. The manual's only owner step is the reset: Cancel, or power off at the breaker for 5 minutes. If iC0 returns, book a technician.

PFOwner checks first

Power

PF means the dishwasher lost power. Press START/CANCEL to clear the code and begin a new cycle. After a hard power failure, the 2020 guide says pressing Start within 18 hours can resume the cycle where it stopped.

CLOwner checks first

Door

CL, also shown as Cd, means the dishwasher door hasn't been closed and latched. Close it fully and the code clears. If you can't get the door to close, contact service to check it.

HONo action needed

Heat delay

HO, also shown as Hd, means the dishwasher is in Heat Delay or Heater On mode. It's the unit warming the water, and the sources list no steps. Colder incoming water means a longer delay.

Parts selected after a diagnostic.

We don’t list parts for this appliance up front. The technician names any part after the diagnostic and matches it to your exact model before anything is replaced.

Faint line drawings of appliance parts on a dark warm texture

Component reference

We have no illustrated entry for this part yet. Follow the system named in the explanation and the manual cited for your model; a code by itself never tells you what to replace.

Explore the researched parts

Call it in tonight.
Cook on it tomorrow.

Three short stages.
Plain, and kept short.

  1. Technician in a dark uniform carrying a toolbox into a warm kitchen
    1

    Book it online

    Pick the appliance, describe the problem and add the model number if you have it. The booking form is open 24/7.

  2. Hands twisting a white water filter into the upper corner of a refrigerator
    2

    We test it on site

    The technician checks the range, fridge or washer, explains what failed and quotes the repair before starting.

  3. Warm walnut kitchen with a stainless French-door refrigerator and granite counters
    3

    Back to normal

    Parts are fitted, the work is tested, and you see the appliance running before the technician leaves.

Prepare for the dishwasher visit.

  1. 1

    Photograph the code

    Older panels show i10, i20, i30, i50, i60 or iC0; newer ones show E10, E20 and so on. Note which one and when it appears.

  2. 2

    Try the door and the cancel key

    Frigidaire says the unit won’t start unless the door is latched. Hold Cancel to clear a delayed start.

  3. 3

    Clean the filter and glass trap

    A clogged filter can cause drain and leak trouble, per Frigidaire’s leak and drain articles.

  4. 4

    Check the drain line

    Look for a kinked drain hose and, after a new disposer, a knockout plug still in the inlet.

  5. 5

    Use dishwasher detergent only

    Hand soap oversuds and may leak.

Leave internal testing to a technician.

Book a visit if the dishwasher leaks again after the filter, hose and detergent checks.

Book a visit if an i or E code, or flashing lights, return after the power is off for 5 minutes.

Switch off the breaker if water reaches the floor near the unit.

Leave the wiring and the pump to the technician.

Arrange a diagnostic

Real scope. Clear expectations.

9US metro areas
8Appliance types
38Code explanations

The agreement comes first.

Before work starts

The technician quotes the work to you at the visit, after looking at the appliance, and nothing is done until you say yes.

Workmanship coverage

If Frigidaire’s warranty covers the problem, Frigidaire does that repair. Work we do is covered by our own workmanship warranty.

Here to help

Good questions.
Clear answers.

Talk to our team
What does i10 mean on a Frigidaire dishwasher?

i10 means a low fill was detected: not enough water came in. Check that the water supply is on and the hose is not kinked. If it returns, book a technician.

What do the flashing lights on my dishwasher mean?

Frigidaire links the patterns to a power failure, an unclosed door or a shorted keypad. Press Start/Cancel, close the door, or power off for 5 minutes. If it persists, book a visit.

Why won’t my Frigidaire dishwasher start?

Check power, a fully latched door, a delayed start and any displayed code. Frigidaire also notes the water must be turned on. Still dead after that, book a technician.

Do you fix both i and E code dishwashers?

Yes. Frigidaire’s i-code and E-code manuals list the same problems with a different prefix. Tell us which you see.

Is a dishwasher repair under Frigidaire’s warranty?

If your unit is under Frigidaire’s warranty, Frigidaire handles that repair. Otherwise book a visit with us; the price is agreed before we start.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.