Frigidaire dishwasher i30 / Leak

Frigidaire dishwasher
error i30

Dishwasher / display referencei30

i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.

Also shown as i30

Last reviewed

Dishwasher / display referencei30
Meaning
i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.
Who handles it
Owner checks first, then a technician
Related codes
Source
Dishwasher Use & Care, A117867311

What Frigidaire dishwasher i30 means.

What it means

i30 means the dishwasher has detected a leak or overflow of water in the bottom pan. Check for loose connections at the water inlet valve and make sure the unit is level, then reset it. If i30 stays, book a technician.

What you can safely check

Look for loose connections at the water inlet valve, the step the manual lists first for i30.

When to call a technician

i30 comes back after the connections, the leveling and the reset have been checked.

Your checklist / kept on this device

Safe checks, in order.

0 of 4 checks done
  1. Frigidaire dishwasher i30: Row of small touch buttons and one glowing light along the top edge of a stainless dishwasher door, seen at a low angle.
    Illustration. Follow your model’s instructions.
    Before you begin

    Check the water inlet valve

    Look for loose connections at the water inlet valve, the step the manual lists first for i30.

  2. Open dishwasher tub with the lower rack removed and a shallow pool of water around the cylindrical filter.
    Illustration. Follow your model’s instructions.
    Check 2

    Check that it's level

    Make sure the dishwasher is properly leveled in its opening.

  3. Hand lifting a gray dishwasher spray arm above its hub in an empty tub with the lower rack removed
    Illustration. Follow your model’s instructions.
    Check 3

    Reset it

    Press Cancel, or switch the dishwasher off at the breaker and leave it off for 5 minutes. The manual gives this as the step for every error code.

  4. Technician in a dark jacket seen from behind holding a tablet with an empty checklist, a range in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a technician if it stays

    If i30 remains after the reset, the manual says to arrange service.

Still showing i30?

Tell us the model and what you have already checked, and start the request right here.

Book a visit

Where a leak is caught.

Conceptual dishwasher sectionTub seam / gasketBase panFloat switchInlet valve1234
  1. 1Tub seam / gasket

Simplified schematic; real layouts differ by model. Tap an outlined part for its photo and the check that goes with it.

Parts behind the message.

Brass water inlet solenoid valve with a black coil, two terminals and a threaded hose fitting on a bench.

Component reference

Water inlet valve

The water inlet valve opens to let supply water into the appliance, and shuts to stop it.

Read the definition

A little more context.

Does i30 always mean visible water?

The code reports that water was detected in the bottom pan. The manual doesn't say how much, so check around the unit as well.

Read the supporting manual

The manual behind the message.

Manufacturer document

Dishwasher Use & Care, A117867311

Frigidaire / Electrolux

September 2020 / PDF p.9 (Error Code table)

Manufacturer document

User Manual, Dishwasher, 117825980A

Frigidaire / Electrolux

No date printed / PDF p.10, section 4.5 Error Codes

This code is from the i-code table in the 2020 Use & Care guide. The newer dishwasher manual prints the same table with an E prefix, so read the row in the manual that came with your dishwasher. On the newer display the same row reads E30.

Here to help

Good questions.
Clear answers.

Talk to our team
What is the bottom pan?

The manual uses the term without explaining it. The code says water from a leak or overflow has been detected there, and it names no particular part.

What does the manual say to check?

Loose connections at the water inlet valve and whether the unit is level. After that comes the reset: Cancel, or power off at the breaker for 5 minutes.

Is E30 the same as i30?

On the newer manual's table, yes: it prints the same row with an E prefix. The two documents are separate, so read the one for your dishwasher.

Can I keep running it with i30 showing?

The manual doesn't say. It gives the checks and the reset, then points you to Frigidaire if i30 stays.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.