Frigidaire dishwasher i10 / Water supply

Frigidaire dishwasher
error i10

Dishwasher / display referencei10

i10 means the dishwasher detected a low fill. Check that the water supply line isn't pinched and that the shutoff valve is fully open, then reset the dishwasher. If i10 stays, book a technician.

Also shown as i10

Last reviewed

Dishwasher / display referencei10
Meaning
i10 means the dishwasher detected a low fill. Check that the water supply line isn't pinched and that the shutoff valve is fully open, then reset the dishwasher. If i10 stays, book a technician.
Who handles it
Owner checks first, then a technician
Related codes
Source
Dishwasher Use & Care, A117867311

What Frigidaire dishwasher i10 means.

What it means

i10 means the dishwasher detected a low fill. Check that the water supply line isn't pinched and that the shutoff valve is fully open, then reset the dishwasher. If i10 stays, book a technician.

What you can safely check

Check that the water supply line isn't pinched or kinked.

When to call a technician

i10 comes back after the supply line, the shutoff and the reset have been checked.

Your checklist / kept on this device

Safe checks, in order.

0 of 4 checks done
  1. Frigidaire dishwasher i10: Row of small touch buttons and one glowing light along the top edge of a stainless dishwasher door, seen at a low angle.
    Illustration. Follow your model’s instructions.
    Before you begin

    Look at the supply line

    Check that the water supply line isn't pinched or kinked.

  2. Open dishwasher tub with the lower rack removed and a shallow pool of water around the cylindrical filter.
    Illustration. Follow your model’s instructions.
    Check 2

    Open the shutoff all the way

    Make sure the water shutoff is completely open.

  3. Hand lifting a gray dishwasher spray arm above its hub in an empty tub with the lower rack removed
    Illustration. Follow your model’s instructions.
    Check 3

    Reset it

    Press Cancel, or switch the dishwasher off at the breaker and leave it off for 5 minutes. The manual gives this as the step for every error code.

  4. Technician in a dark jacket seen from behind holding a tablet with an empty checklist, a range in the background.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a technician if it stays

    If i10 returns after these steps, the manual points to service.

Still showing i10?

Tell us the model and what you have already checked, and start the request right here.

Book a visit

The water-in path.

Conceptual dishwasher sectionSupply valveInlet connectionDishwasher123
  1. 2Inlet connection
  2. 3Dishwasher

Simplified schematic; real layouts differ by model. Tap an outlined part for its photo and the check that goes with it.

Parts behind the message.

Brass water inlet solenoid valve with a black coil, two terminals and a threaded hose fitting on a bench.

Component reference

Water inlet valve

The water inlet valve opens to let supply water into the appliance, and shuts to stop it.

Read the definition

A little more context.

Is i10 a supply problem or a machine problem?

The manual doesn't decide that. It points you to the supply line and the shutoff first, then to a reset.

Read the supporting manual

The manual behind the message.

Manufacturer document

Dishwasher Use & Care, A117867311

Frigidaire / Electrolux

September 2020 / PDF p.9 (Error Code table)

Manufacturer document

User Manual, Dishwasher, 117825980A

Frigidaire / Electrolux

No date printed / PDF p.10, section 4.5 Error Codes

This code is from the i-code table in the 2020 Use & Care guide. The newer dishwasher manual prints the same table with an E prefix, so read the row in the manual that came with your dishwasher. On the newer display the same row reads E10.

Here to help

Good questions.
Clear answers.

Talk to our team
What counts as a low fill?

The manual says only that a low fill has been detected. It gives no volume, and it names no part, so work through the supply checks first.

Where is the water shutoff?

The manual doesn't say. It's usually on the supply line to the dishwasher; if you can't tell which valve is yours, don't force one.

Does the reset need a tool?

No. Press Cancel, or switch the dishwasher off at the breaker for 5 minutes, as the manual describes.

Is E10 the same code?

The newer manual lists the same row as E10. It's a separate document from the 2020 guide, so use the table that matches your dishwasher.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.