Start from the symptom
Frigidaire dishwasher not cleaning.
Start with the cycle and the loading, then the detergent, then the filter, glass trap and spray arms. Frigidaire’s cleaning article also says to run an empty cycle on the highest heat setting. An i40 code means food has built up in the filter or sump.

Start with safe observations.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Which cycle
A Rinse cycle won’t clean dishes, and Quick Wash or 30 minute cycles may not clean heavy soil.
- 2
How it was loaded
Poor loading means poor cleaning. Don’t nest items, and keep anything from blocking the spray arms.
- 3
Detergent
Powder, liquid or tablets all work. Stay within the recommended amount and the max fill line. Detergent left in the cup afterwards means something blocked the dispenser.
- 4
Clean the filter, glass trap and spray arms
Debris collects in all three and blocks the water. Twist the cylinder fine filter counterclockwise, lift it out and rinse it, and rinse the coarse filter under running water. Then run an empty cycle on the highest heat setting.
- 5
Water temperature and pressure
Frigidaire wants water of at least 120°F. Run the sink hot first. Low pressure, such as when a shower or washer is running, also hurts cleaning.
Systems a technician may investigate.
These parts are linked to the problem. What you noticed does not prove any one of them has failed.
If the display adds a code.
Drain
i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.
Drain
i20 means clogged filters or a restricted drain line were detected, and Frigidaire's article adds that the unit didn't drain completely. Clean both filters and the sump, check the drain hose, then reset the dishwasher.
Read the related care guide.

Strange noise from the dishwasher? Start here.
Most dishwasher sounds are part of a normal cycle. Frigidaire's noise guide lists hissing from the water valve, humming from the wash and drain pumps, clunks from the detergent cup and ball valve, and whooshing spray arms. A knock or bang usually means something is hitting a spray arm.

Spotty glasses and damp dishes? Check the rinse aid first.
Fill the rinse aid dispenser to the indicated level without overfilling, raise the L0 to L6 setting one step if you see spots and poor drying, and keep the detergent dose matched to your water hardness.
When observation becomes a service request.
Leave internal testing to a technician.
If the dishes are still dirty once the filter and spray arms are clean and you’ve tried a heavier cycle, book a technician. An i40 code that returns after cleaning is also one for a technician.
Arrange a diagnosticSources and model boundaries.
These documents back up the Frigidaire dishwasher not cleaning advice. Use the manual that matches your model.
- Dishwasher - Not Cleaning (KB 1831286)
- Dishwashers - How can I ensure the best cleaning results? (KB 1847432)
- Dishwasher Glass Trap and Filter Guide (KB 1829617)
- Dishwasher Use & Care, A23587501B
Follow the instructions written for your own model. See how we research these pages.
What does i40 mean?
A clogged filter or sump: food soils have built up. Clean the glass trap and filter and run again. If i40 continues, book a technician.
How often should I clean the filter?
The sources give no schedule. They say to clean the filter, glass trap and spray arms whenever cleaning drops off, and to check the glass trap is installed properly.
Does hot water make a difference?
Yes. Frigidaire recommends at least 120°F and says running the sink hot before starting helps, since the dishwasher uses only about 3 to 4 gallons per cycle.
Can I use any detergent?
Use automatic dishwasher detergent in powder, liquid or tablet form. Frigidaire warns other soaps over-suds and says not to exceed the max fill line.
Code / problem / part / repair
From the code to what you do next.
i40
i40 means a clogged filter or sump: food soils have built up there. Clean out the glass trap and filter and run the dishwasher again, and check the drain hose. If i40 continues, book a technician.
Frigidaire dishwasher noises
Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.
Dishwasher filter and glass trap
The filter system at the bottom of the dishwasher tub catches food soil so it doesn’t clog the drain. Frigidaire’s guide covers a coarse filter and a cylinder fine filter, which also catches glass, bones and pits. A clogged one is behind i20 and i40, poor cleaning and slow draining.
Dishwasher repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.
