Error codes explained

Frigidaire dishwasher codes: messages, i-codes and E-codes

Frigidaire dishwashers show two kinds of messages. Status messages such as CL, LOC, Hd and PF are normal or easy to clear. Error codes, the i-codes (E-codes on newer panels), mark a low fill, a clog, a leak, a motor, a heater or the control board.

Stainless dishwasher control area with a soft blue glowing status window above a folded striped towel on the handle.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • CL, Cd, LOC, Hd, HO, the hour counts and L0 to L6 are status messages, not errors. 134
  • The i-code table and the E-code table list the same problems with different prefixes. 12
  • The manuals' reset for any error code is Cancel, or the breaker off for 5 minutes. 12
  • i20 has a second reset on Frigidaire's Owner Center: unplug for 3 minutes. 37
  • ER, UO and UF appear in neither Frigidaire table, so we give them no meaning. 12

What do Frigidaire dishwasher codes mean?#

Your Frigidaire dishwasher shows two different kinds of display. Status messages, such as CL, LOC, Hd, PF and L0 to L6, are normal or easy to clear. Error codes, the i-codes or E-codes, point to a low fill, a clog, a leak, the motor, the heater or the control. 123

The prefix matters. Frigidaire's September 2020 use-and-care guide prints its table with a lowercase i: i10, i20, i30 and so on. A newer manual for a panel with an E-code display prints the same problems with an E: E10, E20, E30. We read both and name the manual wherever the two differ. 12

Neither document lists the models it covers. Each is written for a family of dishwashers. For any message that is not in the Owner Center's short list, Frigidaire points you to your owner's manual, and the manual supplied with your unit is the one that matches your panel. 124

Which dishwasher messages are not errors?#

CL (or Cd), LOC, Hd (or HO), the delay hours, the minutes counter and L0 to L6 are not error codes. They tell you what the dishwasher is doing or what it wants from you. PF is also a status, though it is worth knowing. 134

On the displayWhat it tells you
01 to 24A delay start is set. The cycle begins when the count reaches zero. 36
1 to 199Minutes left in the cycle. 34
LOCThe door is locked. 34
CL, Cd or CloseThe door is not closed and latched. 34
Hd or HOHeat Delay or Heater On: the unit is heating the water. 3
L0 to L6The rinse aid dosage level, on some models. 124
PRESS STARTAn instruction, not an error: close the door within 5 seconds of pressing Start. 3
PFThe dishwasher lost power. 13

Three of these have their own pages here:

  • CL or Cd: close and latch the door and the display clears.
  • Hd or HO: a heating delay; colder water means a longer wait, about 1 to 2 minutes for each degree of rise. 3
  • PF: press START/CANCEL, then start a new cycle. After a hard power failure, pressing Start within 18 hours resumes the cycle. 13

If a delay start is the reason nothing is happening, the Owner Center says pressing Cancel once starts the cycle at once. A second press cancels the cycle and begins a drain, and a third cancels the drain and shuts the unit off. 6

What do the i-codes and E-codes mean?#

Each code names a problem area: i10 a low fill, i20, i40 and iF0 a clogged filter or restricted drain, i30 a leak in the bottom pan, i50 the drain or wash motor, i60 the water heating system, and iC0 the electronic control. The E-codes are the same list. 12

The two manuals print these meanings in nearly the same words. A few details are worth keeping:

i-codeE-codeProblemWhat the manual says to look at
i10E10A low fillA pinched supply line, or a water shutoff that is not fully open. 12
i20, i40, iF0E20, E40, EF0Clogged filters or a restricted drain lineClean both filters and the sump area; check the drain hose for pinching or a blockage; if the drain goes to a disposer, check the knockout plug is removed. 12
i30E30Leak or overflow in the bottom panLoose connections at the water inlet valve; make sure the unit is level. 12
i50E50Problem with the drain or wash motorCancel or breaker off for 5 minutes. 12
i60E60Problem with the water heating systemReset; service is needed if it does not clear. 12
iC0EC0Problem with the electronic controlCancel or breaker off for 5 minutes. 12

Frigidaire's two tables differ in one small way. The i-code manual prints iC0 for the control row, and the E-code manual prints EC0 rather than E-C0. We follow each manual's own spelling. 12

Every one of these is covered on a separate page, checks in order:

  • i10, the low fill code.
  • i20 and i40, the clog and drain codes.
  • i30, the leak code.
  • i50, the motor code.
  • i60, the heating code.
  • iC0, the control code.

How do I reset a dishwasher code?#

Press Cancel, or switch the dishwasher's breaker off for 5 minutes, then restart a cycle. That is Frigidaire's footnote for every code in both manuals. If it does not clear, the manuals move to service. 12

The Owner Center describes i20 slightly differently. It lists three resets: press Cancel, cut power at the breaker, or unplug the dishwasher for 3 minutes. The manuals say 5 minutes at the breaker. Both are Frigidaire's, and neither is wrong. If one does not work, there is no benefit in repeating it more than once. 137

  1. 1

    Press Cancel#

    This is the first reset in both manuals. Press or hold it, as the Owner Center says, then start a new cycle. 126

  2. 2

    If the code stays, cut the power#

    Leave its breaker off for 5 minutes. For i20, the Owner Center also allows unplugging for 3 minutes. 13

  3. 3

    Start a short cycle#

    Close the door firmly so the latch engages, then watch whether the same code returns. 3

  4. 4

    Stop after one round#

    If the code returns, further resets will not help. Note it down and book a visit. 1

For i20 and i40, the clog codes, the checks come before the reset. The Owner Center asks you to confirm the disposer knockout plug is out, the drain hose is not blocked or pinched, the hose is at least 32 inches from the floor, and the filters and sump are free of food. For i40 it suggests cleaning the glass trap and filter and running the unit again. 378

What if my code is not in the table?#

Then Frigidaire has not defined it, and we will not guess at one. ER, UO and UF are not in the i-code table, the E-code table or any Owner Center dishwasher article we read. For any code, the manual's footnote applies: Cancel, or breaker off for 5 minutes. 123

Each page says the same in short form. An undocumented code that survives the reset is a question for a technician with the unit open, not for a code list.

What do flashing lights on a Frigidaire dishwasher mean?#

Frigidaire's flashing-lights article describes three light patterns. A power failure flashes the Hi-Temp Wash and Heat Dry lights. A door that is not closed flashes Cycles, Option and Washing. A shorted keypad drains the unit and flashes the status lights. 5

For the power failure pattern, press Start/Cancel to stop it. For the door pattern, close the door and the flashing stops. The keypad pattern is the one to take seriously: Frigidaire says turning the power off for 5 minutes may clear it, and that service should be scheduled for a possible keypad replacement if it continues. 5

When should I book a technician for a dishwasher code?#

Book when an error code survives the Cancel and 5-minute reset, when i30 or E30 comes with water in the base, or when i50, i60 or iC0 stays after the reset. Status messages such as CL or Hd are not reasons to book. 123

If the dishwasher was installed in the last 30 days, Frigidaire's Owner Center asks you to go back to the installer first. After that, a repeating error code is a service call. Tell the technician the code exactly as shown, plus the model and what you have tried. 6

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under Frigidaire's warranty, Frigidaire handles that repair. We give a warranty on our workmanship. When you are ready, schedule a visit with us, or see the dishwasher service page.

Sources#

  1. Dishwasher Use & Care, A117867311Frigidaire / Electrolux · September 2020 · PDF p.9 (Status Window, User Instruction Code, Error Code table)
  2. User Manual, Dishwasher, 117825980AFrigidaire / Electrolux · No date printed · PDF p.9 (Status Window); p.10 (4.5 Error Codes)
  3. Dishwasher Error Codes and Alarms Guide (KB 1829620)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  4. What do I do if my dishwasher is showing a message code? (KB 1852991)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  5. Dishwashers Flashing Lights (KB 1829621)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  6. Dishwasher Error Code 01-24, Delayed option activated (KB 1830334)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  7. Dishwasher Error Code i20 (KB 1830367)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  8. Dishwasher Error Code i40 (KB 1831281)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text

Here to help

Good questions.
Clear answers.

Talk to our team
Is CL on my dishwasher an error?

Not really. CL, Cd or Close means the door is not shut and latched. Closing it clears the display, and Frigidaire's older manual states that this does not indicate a problem and service does not need to be contacted. See sources 1 and 3.

Why does the dishwasher show Hd or HO and then pause?

Hd or HO means Heat Delay or Heater On: the dishwasher is waiting for the water to reach the right temperature. Frigidaire says colder incoming water means a longer wait, about 1 to 2 minutes per degree of rise. See source 3.

Is an E-code the same as an i-code?

On the two Frigidaire manuals we hold, yes. The E-code manual repeats the i-code table with an E prefix, so E10 matches i10 and E30 matches i30. The control row differs: one prints iC0 and the other EC0. See sources 1 and 2.

What does PF mean after a power cut?

PF means the dishwasher lost power. Press START/CANCEL to clear it and start a new cycle. The 2020 manual adds that after a hard power failure, pressing Start within 18 hours resumes at the point of interruption. See sources 1 and 3.

My dishwasher shows ER, UO or UF. What are those?

Frigidaire's dishwasher code tables and Owner Center articles do not list them. The manual's footnote for any code is to press Cancel or switch the breaker off for 5 minutes. If it comes back, arrange a visit. See sources 1 and 2.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.