Diagnostics and repair
An experienced technician checks the appliance before suggesting any work. OEM parts can be ordered, matched to your exact model.
The care journal
What your display code means, how it differs from similar codes, and what to try first.

Frigidaire dishwashers show two kinds of messages. Status messages such as CL, LOC, Hd and PF are normal or easy to clear. Error codes, the i-codes (E-codes on newer panels), mark a low fill, a clog, a leak, a motor, a heater or the control board.

Frigidaire's refrigerator alarms split in two. HI, PF, Door Ajar, DI SP, Sb and 77 77 are things you can clear: close a door, acknowledge the alarm, clear a jam or leave a mode. SY CE, SY CF, SY EF, OP and SH are listed as codes that could mean a visit, with no meaning given.

Frigidaire washer codes depend on the type. Top-load washers use E1 to E5, CL and a few F-codes. Current front-load washers use AL alarms such as AL 10 and AL 20. Older front-load E-codes like E11 or E23 are not in any current Frigidaire source.

Frigidaire codes are specific to the appliance type and often to the model, so read the table for yours. Locate the label or plate (inside the door or fresh-food compartment on most units) for the model and serial number, then match the code to that appliance's own manual or article.

Jot down the code exactly as it appears, with any extra characters, before you press anything. We will ask for it at the visit.
Read the full sequence
A flashing 12:00 on a Frigidaire range means the control lost power and forgot the time. The manuals say the clock must be set before the oven will run, so set it first. Then check the 12/24-hour mode, the minute timer, a dash on the display and Delay Start. If the clock keeps resetting without a power cut, book a technician.

Frigidaire’s own fix order starts with preheating, then rack position and bakeware, and only then calibration. Let the empty oven fully preheat with the door shut, then check pans and racks. On electric ovens the article also names low supply voltage and a worn door gasket. If it’s a gas range, read the recall note first.

Before anything else on a gas range, check whether it is covered by the CPSC recall 26-333 for delayed bake burner ignition. If it isn’t, work through Frigidaire’s checks: clock set, the right function started, and for burners the caps, ports and power cord. An electric range that heats nowhere right after install may have a wiring or voltage issue.

The keypad is the set of keys or touch pads that tells the control what to do. Frigidaire lists F1 as “Shorted Key Pad” on range ovens, and its dishwasher guide says a shorted keypad drains the unit and flashes its lights. Both guides begin with a power reset.

The oven door lock is a motorized latch that holds the door shut during a self-clean or when you switch on the lockout. Frigidaire’s range manual says it takes about 15 seconds to lock or unlock, and Frigidaire lists F90 through F94 as door lock codes.

On a Frigidaire gas range each surface burner has a cap, a burner head and an electronic ignitor that sparks when you turn the knob to Lite. If a burner won’t light, Frigidaire starts with the knob, the caps, the ports and the power cord. The oven’s bake burner is a different part, and some gas ranges are under CPSC recall 26-333 for it.
F1 is listed by Frigidaire as “Shorted Key Pad” for range ovens, with no explanation past the name. Press OFF, reset the power, set the clock and retry Bake or Broil. If F1 returns, arrange service.
F3 is listed by Frigidaire as “Communication Error” for range ovens. No cause is printed. F20 and F26 carry the same name in the guide and have their own pages. Press OFF, reset the power, set the clock and retry; arrange service if it returns.
F30 is the entry Frigidaire lists as “Open Probe” for range ovens. The sources give no cause or part beyond the name. Reset the power, set the clock and retry Bake or Broil, then arrange service if F30 repeats.
F31 is listed by Frigidaire as “Shorted Probe” for its range ovens, and the sources add no cause beyond that name. Press OFF, reset the power, set the clock and try Bake or Broil again. If F31 comes back, arrange service.
Frigidaire does not list F2 for ovens. F2 shows up in its articles only for washers, which is a different appliance. For a range, follow the generic F-code steps: OFF, a power reset, set the clock, retry, then book a technician if F2 recurs.
F4 is not defined for ovens in the Frigidaire range manuals or the Owner Center code guide. The only instruction is generic: press OFF, reset the power, set the clock, and try Bake or Broil. If F4 repeats, book a technician.
Frigidaire's range manuals and code guide does not print F0. It lists one generic F or E code row instead. Press OFF, reset the power, set the clock and retry Bake or Broil; arrange a technician if the code keeps coming back.
Frigidaire's range manuals and code guide does not print F7. It lists one row for any F or E code instead. Press OFF, reset the power, set the clock and retry; arrange a technician if the code keeps coming back.
F14 is missing from Frigidaire's range code guide and manuals, so its meaning is unknown to us. Follow the manual's generic sequence, press OFF, cut power, set the clock and retest, and book a technician if the code keeps coming back.
No Frigidaire document we checked defines F15. The range manuals treat any F or E code the same way: press OFF, cut power, reset the clock and try again. If F15 returns after that, book a technician instead of guessing at a part.
An experienced technician checks the appliance before suggesting any work. OEM parts can be ordered, matched to your exact model.
If Frigidaire’s warranty covers the problem, Frigidaire does that repair. Work we do is covered by our own workmanship warranty.
They were written for different products or years. Where they conflict, for example on reset timing, we quote each one with its title so you can see which applies to you.
Frigidaire's documents we read do not give it a meaning. We list what they do say, the safe checks, and when to book. We do not fill the gap with a guess.
Frigidaire's articles list SY CE, SY CF and SY EF only as signs that service is needed. They give no meaning, so our pages give none either.
Photograph it first. Clearing may help a one-off message, but the photo helps the technician if the code was the first sign of a real problem.
Code / problem / part / repair
Frigidaire sorts refrigerator leaks by where the water shows up: outside the unit (back connections and the water valve), inside (the water filter), or at the dispenser (frost in the chute, or air in the line). A door left open can also ice up the evaporator and leak from the bottom. Find the spot first, and book if the source isn’t one of these.
Book a diagnostic for your model, done at your home.
Office addresses and the entry details to have ready.