Error codes explained

Frigidaire washer codes: top-load, front-load and older models

Frigidaire washer codes depend on the type. Top-load washers use E1 to E5, CL and a few F-codes. Current front-load washers use AL alarms such as AL 10 and AL 20. Older front-load E-codes like E11 or E23 are not in any current Frigidaire source.

White top-load washer with a softly blurred glowing display, next to a woven basket of folded towels in a laundry room.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Top-load: E1 slow fill, E2 slow drain, E3 lid, E4 out of balance, E5 not level, CL lid open with control lock. 1
  • Top-load E7, F2, F5, F8, Fd and C9 have no owner steps in the manual. 1
  • Front-load: AL 10, AL 20, AL 40, AL 91, AL F0 and AL H0, with reset steps in the July 2026 guide. 2
  • The same code can differ by type: F2 is PCB failed on top-load, too much soap on front-load. 19
  • Older front-load E-codes (E11, E23 and others) are not in any Frigidaire source we hold. 2

Which Frigidaire washer codes apply to my washer?#

It depends on the type. A top-load washer uses E1 to E5, CL and a few F-codes. A current front-load washer uses AL alarms. Older front-load E-codes such as E11 are not in any current Frigidaire document. Identify the type first, then read only that part. 12

The reason to start there is that the same letters mean different things. F2 is the clearest case. In the top-load manual it means the control board failed. In an Owner Center article for front-load washers it means too much soap or the wrong soap, often with suds overflowing. Borrowing a meaning from the other table would be a guess. 19

One more detail helps with top-load washers. The manual prints its code column as small symbols, and Frigidaire's articles say the washer displays the code as a bare number: code 1 for E1, code 3 for E3, and so on. If your display shows only a digit, check the E-code with that number. 135

What do top-load washer codes E1 to E5 and CL mean?#

On a top-load Frigidaire, E1 is a slow or no fill, E2 a slow or failed drain, E3 an open lid or a lid lock problem, E4 an out-of-balance load in spin, E5 an unlevel washer, and CL a lid left open with the control lock on. Each has owner checks. 1345678

CodeFrigidaire's meaningOwner checks from the manual and articles
E1Water is not entering, or fills slowly (over 30 minutes at low level, 45 at medium, 60 at high)Lid closed; hot and cold taps fully open; supply pressure; kinked hoses; clean the hose screens; look for water leaking from the tub. 13
E2Water takes more than 10 minutes to drainFuse or breaker; standpipe height; lid closed and Start/Pause pressed; kinked or clogged drain hose. 14
E3The lid is open, or the lid lock failedLid fully closed; washer level. If the lid still does not lock, the lid lock or circuit board may have failed. 15
E4Out of balance during spinWasher firm on the floor, legs adjusted; foam shipping support removed; load not piled to one side. 16
E5The washer is not level (impact switch failed)Make sure it is level and not leaning back; adjust the legs. 17
CLLid open over 20 seconds with Child Lock onPower off; switch Child Lock off. 18

E4 deserves a second look. The washer tries to fix an unbalanced load itself, and after three failed attempts the article asks you to redistribute the clothes. It also calls an unlevel washer a common installation issue and says that for a unit installed or moved in the last 30 days, you go back to the installer. 6

  1. 1

    For E1, check the water side#

    Open both taps fully, straighten the inlet hoses and clean the hose screens. Look under and around the tub for leaks. 13

  2. 2

    For E2, check the way out#

    Inspect the drain hose for bends or a clog, and the standpipe height. Close the lid and press Start/Pause. 14

  3. 3

    For E3, E4 and E5, check lid and level#

    Close the lid fully, then confirm the washer sits level on all four legs and the shipping foam is gone. 567

  4. 4

    For CL, power off and release the lock#

    Switch the Child Lock off as the manual's setting page describes. 8

Which top-load codes give no owner steps?#

E7, F2, F5, F8, Fd and C9. The manual lists them with a one-line meaning and no checks, and the only instruction is to call service. They are Hall sensor failed, PCB failed, load sensing failed, water level sensor failed, door lock failed and PCB failed. 1

These are the rows that point straight to a visit, and trying things from the earlier table will not help. Note the code and the moment the washer showed it, then book. 1

Why E1 and E2 mention minutes#

The manual ties both codes to a clock. E1 appears when filling takes longer than 30 minutes at the low water level, 45 at medium or 60 at high, or when the water level has not changed in five minutes during filling. E2 appears when draining takes more than 10 minutes. A slow supply or a slow drain can therefore trigger them without anything having broken, which is why the hose and tap checks come first. 1

What do the front-load AL codes mean?#

Current Frigidaire front-load washers flash AL alternating with a two-character code. The July 2026 guide lists six: AL 10 (not filling properly), AL 20 (not draining properly), AL 40 (door open or not fully shut at Start), AL 91 (internal communication), AL F0 (anti-flood device) and AL H0 (power supply). 2

AlarmFrigidaire's meaningWhat the guide asks
AL 10Not filling with water properlyTap fully open; enough water pressure; tap not clogged; inlet hose without kinks and properly connected; hose filter not clogged; then reset. 2
AL 20Not draining properlyDrain hose without kinks, clogs and connected properly; house drain pipes clear (a plumber if necessary); then reset. 2
AL 40Door open or not shut completely when Start is pressedClose the door completely; reset. 2
AL 91Disruption in internal communicationReset. 2
AL F0The anti-flood device has been activatedClose the water taps, unplug the washer, then call for service. 2
AL H0A power supply issueWait until the supply is stable; check the cord and the wall outlet; reset. 2

The reset is the same everywhere in that table: turn the knob to the reset position (12 o'clock) or cut power to the washer and restore it. For any alarm not in the table, reset first, and if it reappears, the guide says to contact service. 2

What about older front-load E-codes like E11 or E23?#

Frigidaire does not decode them. E11, E23, E58, E35, E43, E57, E56, E47, E59 and E21 are not in the current front-load guide, which uses AL alarms instead, and they are not in the top-load manual either. We give them no meaning. 12

For a washer that shows one of these, the general guidance from Frigidaire's current front-load guide is the same reset: knob to 12 o'clock or power off and on. If it returns, or the washer will not fill, drain or spin, a technician can inspect the unit in person. 2

When should I book a technician for a washer code?#

Book when a code returns after the checks in your table, for any top-load E7, F2, F5, F8, Fd or C9, for AL F0, and for an older E-code that survives a reset. Alarms you clear with a closed lid or a level machine do not need a visit. 12

The Owner Center adds a limit: for a unit installed in the last 30 days, go back to the installer first. After that, a repeating code is a service call. Say which type of washer you have, the code as displayed and which checks you did. 46

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under Frigidaire's warranty, Frigidaire handles that repair. We give a warranty on our workmanship. When you are ready, schedule a visit with us, or see the washer service page.

Sources#

  1. All about the Use & Care of your Washer, A29259301Frigidaire / Electrolux · August 2024 (retailer-hosted copy of the Frigidaire document) · PDF p.18 (Avoid Service Checklist, Error Codes)
  2. Front Load Washer Use & Care Guide, A33032801Frigidaire / Electrolux · July 2026 · PDF p.30 (Solutions to Common Problems, alarm codes)
  3. Top Loading Washer - Error Code E1 long fill time (KB 1829698)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  4. Laundry top loading washer Error Code E2 (KB 1829699)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  5. Laundry top loading washer Error Code E3 (KB 1829706)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  6. Laundry top loading washer Error Code E4 (KB 1830117)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  7. Laundry top loading washer Error Code E5 (KB 1830380)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  8. Laundry top loading washer Error Code CL (KB 1831069)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
  9. Washer Displaying Error Code F2 too many suds or suds overflowing (KB 1825280)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text

Here to help

Good questions.
Clear answers.

Talk to our team
My washer shows just a number, like 1 or 3. Is that E1 or E3?

Often yes. Frigidaire's top-load E-code articles say the washer displays the code as a bare number, for example code 1 for E1 and code 3 for E3. The manual prints the codes as small symbols. See sources 1, 3 and 5.

Is the same code the same on every Frigidaire washer?

No. F2, for example, means PCB failed in the top-load manual and too much soap on front-load washers in an Owner Center article. Identify your washer type first, then read only that table. See sources 1 and 9.

What does AL mean on my washer?

AL is the prefix of Frigidaire's current front-load alarm codes. The display alternates AL with a two-character code such as 10 or F0. The July 2026 guide lists six: AL 10, 20, 40, 91, F0 and H0. See source 2.

Why does E4 keep coming back?

E4 means the load went out of balance during spin. The washer retries on its own, and after three failed attempts you should redistribute the clothes. The article also asks you to check the foam shipping support was removed and the legs are adjusted. See source 6.

Can I clear CL on a top-load washer?

Yes. CL means the lid stayed open more than 20 seconds with the control lock on. Power the washer off and switch the Child Lock off, as the manual describes. See sources 1 and 8.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.