Inside the appliance
Dishwasher heating element. In plain English.
The heating element warms the water and helps dry the load. Frigidaire’s manual lists it among the dishwasher’s parts and warns that it stays hot, so let it cool before cleaning the tub. i60 means a problem with water heating, and HO or Hd means Heat Delay or Heater On mode, a heating step rather than a problem.

Where it fits.
Dishwasher heating element in the appliance
It is inside the tub, listed as part K in the dishwasher’s parts diagram. Frigidaire’s manual warns it stays hot after a wash, so don’t touch it.
The photo shows the kind of part. It is not a guide to the right replacement for your model.
What you notice when this part needs attention.
Trouble with the Dishwasher heating element can show up as weaker performance or a code that keeps coming back. Only testing shows whether this part is the cause.

Frigidaire dishwasher noises
Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.

Frigidaire dishwasher leaking
Stop the dishwasher and shut off its water supply before anything else. Frigidaire’s leak article starts with the drain hose, the door and the supply connections, then asks about filters, detergent and spilled rinse aid. An i30 code means the unit sensed water in its bottom pan.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Let it cool
The manual warns of burns: allow the heating element to cool before cleaning the interior, and don’t touch it during or just after a wash.
- 2
Read HO or Hd properly
Frigidaire says the code means Heat Delay or Heater On mode, which is the unit warming the water. Colder incoming water can lengthen the delay, so wait before assuming a problem.
- 3
Check what drying needs
For wet dishes, Frigidaire says to use the Heat Dry option with a rinse aid, and that Quick Wash cycles may not dry fully. Plastic and bowls retain some water.
- 4
Look at your water heater
Frigidaire recommends a water heater set to at least 120 degrees, and running the kitchen tap hot before starting a cycle.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if i60 appears and returns after the reset, or if dishes stay cold and wet with Heat Dry on. Switch the unit off at the breaker before anything else, and don’t touch the element.
Arrange a diagnosticSources and model boundaries.
These documents back up the Dishwasher heating element advice. Use the manual that matches your model.
- Dishwasher Use & Care, A23587501B
- Dishwasher Use & Care, A117867311
- Dishwasher Error Code Hd or HO - Heat delay or heater on mode activated (KB 1830362)
- Dishwasher - Not Drying (KB 1819543)
Follow the instructions written for your own model. See how we research these pages.
What does i60 mean?
Frigidaire’s table says a problem has been detected with the water heating system. The only owner step is the reset: press Cancel or turn power off at the breaker for 5 minutes. If i60 stays, book a technician.
Is HO a problem?
No. Frigidaire says HO, also shown as Hd, means Heat Delay or Heater On mode is active. It is the dishwasher warming the water, and colder incoming water means a longer delay.
Why aren’t my dishes drying?
Frigidaire lists several non-part causes first: plastics and concave bowls hold water, Quick Wash cycles may not dry fully, and drying works better with Heat Dry plus rinse aid.
Can I touch the heating element?
No, not during or right after a wash. The manual warns of burns and says to let it cool before you clean the interior.
Code / problem / part / repair
From the code to what you do next.
i60
i60 means a problem has been detected with the water heating system. The manual gives one owner step, the reset: Cancel, or power off at the breaker for 5 minutes. If i60 stays, service will be needed.
Frigidaire dishwasher noises
Most dishwasher sounds are part of a normal cycle. Frigidaire’s noise guide lists hissing from the water valve, humming from the wash and drain pumps, and a clunk when the detergent cup opens. A knock or bang usually means something is hitting a spray arm.
Dishwasher repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.

