Before work starts
The technician quotes the work to you at the visit, after looking at the appliance, and nothing is done until you say yes.
Independent appliance repair
Frigidaire top-load and front-load washers come to us when the tub stalls, the water stays, a cycle never begins, or the floor gets wet. Tell us whether the lid or door locks, what the display says and where the water stops, then book a visit.


On a top-load Frigidaire, the usual cause is an unbalanced load or a lid that isn’t closed. Frigidaire’s tub-not-spinning article says to power off, wait for the lid to unlock, rearrange the clothes and restart. After that it checks load size, shipping materials, level and hose connections.

On a top-load Frigidaire, check the drain hose and standpipe first, then detergent. E2 means the unit took over 10 minutes to drain. Frigidaire’s article asks if the washer has been moved, if the hose is kinked, and if the standpipe is the right height.

Work through Frigidaire’s list: level, Start pressed, Delay Start, lid closed, power, water and breaker. A washer left on for more than 10 minutes without Start pressed switches itself off. On top-load models the lid must be fully closed, and CL means it was left open with Child Lock on.

Find where the water comes from before you touch anything: inlet hose, drain hose, or the lid and underneath. Frigidaire’s order of checks is hoses and connections, the drain, then shipping bolts and level. Shut off the water first.

Many washer sounds are normal, but banging and shaking usually trace to level, the load or shipping parts. Frigidaire’s noise guide asks first whether the washer is new, then whether it’s level and on firm flooring. Thumping at the start of a spin with a heavy load is common.

Frigidaire’s guide is mostly about what goes where: powder or liquid in the main wash cup below the max line, packs directly in the drum, bleach and softener in their labeled compartments. A clogged dispenser or too many suds usually means the wrong product or too much.

Frigidaire links washer odors to damp laundry and trapped moisture. Take clothes out promptly, leave the lid open between loads, wipe the washer down and run the Tub Clean cycle on schedule. Its care article names no other cause.
We have not researched code meanings for this appliance yet. Use its manual and add a photo of the display to your request.
See the research statusWe don’t list parts for this appliance up front. The technician names any part after the diagnostic and matches it to your exact model before anything is replaced.

We have no illustrated entry for this part yet. Follow the system named in the explanation and the manual cited for your model; a code by itself never tells you what to replace.
Explore the researched partsThree short stages.
Plain, and kept short.

Pick the appliance, describe the problem and add the model number if you have it. The booking form is open 24/7.

The technician checks the range, fridge or washer, explains what failed and quotes the repair before starting.

Parts are fitted, the work is tested, and you see the appliance running before the technician leaves.
Top-loaders use E1–E5 and F-codes; Frigidaire’s current front-loaders list alarms such as AL 10 and AL 20.
For a tub that won’t spin, Frigidaire says turn power off, wait for the lid to unlock, rearrange the clothes and restart.
Kinked drain hoses and hoses sealed airtight in the standpipe cause slow draining; leaks often start at loose fill hoses.
Make sure the washer is level and shipping materials are removed.
Frigidaire says high-efficiency detergent in the right amount; too much can overflow or stop draining.
Book if the tub stays still or the water stays put once you have rebalanced the load and checked the hoses.
Book a visit if an E, F or AL code returns after a power reset.
Turn off the water taps and unplug the washer if water is leaking.
Leave the motor and the electronics to the technician.
Arrange a diagnosticThe technician quotes the work to you at the visit, after looking at the appliance, and nothing is done until you say yes.
If Frigidaire’s warranty covers the problem, Frigidaire does that repair. Work we do is covered by our own workmanship warranty.
An unbalanced load is the first thing Frigidaire names. Power off, wait for the lid to unlock, rearrange the load and restart. If it still won’t spin, book a technician.
On the top-load table, E2 means the water takes too long to drain. Check the drain hose and standpipe, then book a visit if it returns.
Yes, top-load and front-load. Current front-loaders show AL alarms such as AL 10 for a fill problem; tell us which code you see.
Frigidaire lists an open lid, a Delay Start, a loose plug, closed water taps or a tripped breaker. Check those, then book a visit if it stays dead.
If your unit is under Frigidaire’s warranty, Frigidaire handles that repair. Otherwise book with us; the price is agreed before work starts.
Code / problem / part / repair
On a top-load Frigidaire, the usual cause is an unbalanced load or a lid that isn’t closed. Frigidaire’s tub-not-spinning article says to power off, wait for the lid to unlock, rearrange the clothes and restart. After that it checks load size, shipping materials, level and hose connections.
Book a diagnostic for your model, done at your home.
Office addresses and the entry details to have ready.