Start from the symptom
Frigidaire washer not draining.
On a top-load Frigidaire, check the drain hose and standpipe first, then detergent. E2 means the unit took over 10 minutes to drain. Frigidaire’s article asks if the washer has been moved, if the hose is kinked, and if the standpipe is the right height.

Start with safe observations.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Hose kinks and recent moves
Has the washer moved or the hose been knocked? Straighten a kinked drain hose and make sure the house drain isn’t clogged.
- 2
Standpipe height and fit
Frigidaire says a top-load washer’s standpipe cannot be higher than 96 inches, and the drain hose shouldn’t be sealed tight into it, because the standpipe needs air. The manual says a standpipe under 36 inches can let water siphon. A front-load washer’s manual has different figures: a maximum of 56.5 inches and a minimum of 24 inches.
- 3
Standpipe size and distance
The standpipe needs a diameter of at least 1 1/4 inches. If it is too far from the washer, Frigidaire says moving the washer closer, if possible, can help.
- 4
Detergent
Too much detergent can stop draining. Don’t fill any dispenser compartment past its max line.
- 5
Clogged pipes
Check the drain hose and drain pipe. A plumber is the right call for a clogged house drain.
- 6
Lid lock
If water is in the tub and the drain and spin cycles didn’t run, the manual points to the lid lock. Don’t bypass it.
Systems a technician may investigate.
These parts are linked to the problem. What you noticed does not prove any one of them has failed.
If the display adds a code.
Keep the exact message.
We have not researched code meanings for this appliance yet. Use its manual and add a photo of the display to your request.
See the research statusRead the related care guide.

Smelly washer? A monthly Tub Clean and an open lid do most of the work.
Clean a Frigidaire top-load washer by running Tub Clean about once a month with one cup of liquid chlorine bleach or a washing machine cleaner pouch, then Rinse & Spin. Between times, empty it promptly and dry the lid area.

A code on your Frigidaire washer? Find your type first.
Frigidaire washer codes depend on the type. Top-load washers use E1 to E5, CL and a few F-codes. Current front-load washers use AL alarms such as AL 10 and AL 20. Older front-load E-codes like E11 or E23 are not in any current Frigidaire source.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit if the checks above are clear and water is still standing in the tub, or if E2 comes back. Keep the plug out while you work near standing water, and don’t force the lid. Frigidaire says a washer installed or moved in the last 30 days goes back to the installer first.
Arrange a diagnosticSources and model boundaries.
These documents back up the Frigidaire washer not draining advice. Use the manual that matches your model.
- Laundry top loading washer is not draining (KB 1834688)
- All about the Use & Care of your Washer, A29259301
- Front Load Washer Use & Care Guide, A33032801
Follow the instructions written for your own model. See how we research these pages.
What does E2 mean on a Frigidaire washer?
The top-load manual says the unit took more than 10 minutes to drain. Check the drain hose for kinks and the drain for clogs, as in the manual’s does-not-drain checks, then restart.
Can too much detergent stop the washer draining?
Yes. Frigidaire says it can. Keep each dispenser compartment below its max fill line.
What if I have a front-load Frigidaire?
It shows AL 20 for slow draining. The manual says to check the drain hose and house pipes, reset, and for water left in the drum, run Rinse & Spin with No Spin.
Does the standpipe height matter?
Yes, and the limits differ by model. Frigidaire’s top-load article says no higher than 96 inches; the front-load manual says no higher than 56.5 inches.
Code / problem / part / repair
From the code to what you do next.
Frigidaire washer not spinning
On a top-load Frigidaire, the usual cause is an unbalanced load or a lid that isn’t closed. Frigidaire’s tub-not-spinning article says to power off, wait for the lid to unlock, rearrange the clothes and restart. After that it checks load size, shipping materials, level and hose connections.
Washer drain pump and filter
The drain pump pushes water out of the washer. On Frigidaire’s front-load washer it has a pump filter behind a small cleanout door, and a clogged filter is one cause of a washer that won’t drain. The manual says a humming or gurgling pump is normal. Pumping sounds that change to rattling may point to something in the pump.
Washer repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.
