Inside the appliance

Dishwasher drain pump. In plain English.

The drain pump moves used water out of the dishwasher. Frigidaire’s noise guide describes its hum as steady at first, then changing as the last water goes out. For i20 Frigidaire checks the hose, the disposer plug and the filters; i50 covers a problem with the drain or wash motor.

Last reviewed

Dishwasher drain pump with white motor housing, gray impeller cover, outlet spout and electrical connector on a bench.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Where it fits.

Dishwasher drain pump in the appliance

Frigidaire’s manuals don’t show where it sits, only that water passes the filter and is pumped out to the drain. It is a service part, not something you reach.

The photo shows the kind of part. It is not a guide to the right replacement for your model.

What you notice when this part needs attention.

Trouble with the Dishwasher drain pump can show up as weaker performance or a code that keeps coming back. Only testing shows whether this part is the cause.

Owner care, within the model instructions.

Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.

  1. 1

    Hear what is normal

    Frigidaire says a hum from the drain pump is usual, steady at first and then fluctuating as the water leaves. It is separate from the wash pump, which starts and stops with the spray arms.

  2. 2

    Check the drain path first

    For i20 Frigidaire lists the disposer knockout plug, a blocked, pinched or restricted hose, a hose height of at least 32 inches from the floor, and a clear glass trap or filter.

  3. 3

    Reset the unit

    Frigidaire’s i20 article says to hold Cancel, switch off at the breaker, or unplug for 3 minutes. The i50 table says to press Cancel or turn power off at the breaker for 5 minutes.

  4. 4

    Look at the display

    Some units flash lights when they don’t drain during a cycle. Frigidaire says this typically signals a drainage issue. Press and hold Cancel for 5 to 10 seconds to clear the cycle.

Cleaning or replacement?

Leave internal testing to a technician.

Book a visit if i50 returns after the reset, or if water remains after the filter, hose and plug checks. Don’t open the pump or reach in with tools.

Arrange a diagnostic

Sources and model boundaries.

These documents back up the Dishwasher drain pump advice. Use the manual that matches your model.

  • Dishwasher Noise Guide (KB 1928400)
  • Dishwasher Error Code i20 - Unit did not drain properly (KB 1830367)
  • Dishwashers - Not Draining
  • Dishwasher Use & Care, A117867311
  • Dishwasher Use & Care, A23587501B

Follow the instructions written for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Should a hum from the drain pump worry me?

Yes. Frigidaire’s noise guide lists a hum from the drain pump as normal, steady at first and changing as the water is pumped out.

What does i50 mean?

Frigidaire’s code table says a problem has been detected with the drain or wash motor. Press Cancel or switch off at the breaker for 5 minutes to clear it. If it returns, book a technician.

Why is there water left after the cycle?

Frigidaire’s checks: knockout plug removed on a new disposer hookup, a clear and unkinked hose, a clean glass trap or filter, and a cycle that has finished rather than paused.

Can I fix a dishwasher that won’t drain myself?

You can do the checks Frigidaire lists: filters, hose, plug and reset. The pump itself sits behind the sump, and opening it isn’t an owner step, so book a visit if those don’t help.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.