Inside the appliance
Washer tub and Tub Clean cycle. In plain English.
Frigidaire’s odor advice for washers starts with moisture: unload wet clothes promptly, leave the lid open when the washer is idle, and run the Tub Clean cycle (also named System Clean or Clean Washer), monthly or every 50 loads depending on model. Front-load guides add the rubber gasket folds.

Where it fits.
Washer tub and Tub Clean cycle in the appliance
The wash tub is the drum inside the washer. On front-load models the manual also names the rubber seal at the front.
The photo shows the kind of part. It is not a guide to the right replacement for your model.
What you notice when this part needs attention.
Trouble with the Washer tub and Tub Clean cycle can show up as weaker performance or a code that keeps coming back. Only testing shows whether this part is the cause.

Frigidaire washer not spinning
On a top-load Frigidaire, the usual cause is an unbalanced load or a lid that isn’t closed. Frigidaire’s tub-not-spinning article says to power off, wait for the lid to unlock, rearrange the clothes and restart. After that it checks load size, shipping materials, level and hose connections.

Frigidaire washer not draining
On a top-load Frigidaire, check the drain hose and standpipe first, then detergent. E2 means the unit took over 10 minutes to drain. Frigidaire’s article asks if the washer has been moved, if the hose is kinked, and if the standpipe is the right height.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Unload and air it out
Don’t leave wet clothes in the washer. Leave the lid open for a while, or whenever the washer is idle, to let humidity out.
- 2
Wipe the outside
Clean the top and sides with a damp cloth or mild soap and water, and avoid moisture build-up.
- 3
Clear residue
After heavily soiled loads, shake or brush off dirt and sand first. If residue remains in the tub, wipe it with a non-abrasive household cleaner and run the Rinse Only cycle.
- 4
Run Tub Clean
Frigidaire says most models have it and to run it monthly or every 50 loads, depending on your model. The top-load manual has you remove all items first and never mix chlorine bleach with other chemicals.
- 5
Front-load models
The front-load guide says the clean washer cycle is paired with care of the rubber gasket folds, and that severe odor or mold may need its longer cleaning procedure. Follow your own manual.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if the odor stays after repeated Tub Clean cycles and an airing routine.
Arrange a diagnosticSources and model boundaries.
These documents back up the Washer tub and Tub Clean cycle advice. Use the manual that matches your model.
- Top Load Washers - How do I care and clean my Frigidaire Top Load washer? (KB 1848678)
- All about the Use & Care of your Washer, A29259301
- Front Load Washer Use & Care Guide, A33032801
Follow the instructions written for your own model. See how we research these pages.
How often should I run Tub Clean?
Frigidaire says once a month or every 50 loads, depending on your model.
Should I leave the lid open?
Frigidaire says to leave it open for a while or when not in use. The top-load manual warns against it if small children or pets are present.
Can I mix bleach with a cleaner?
No. The manual’s warning says never mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acids or ammonia products.
What should I check first for washer tub and tub clean cycle?
Don’t leave wet clothes in the washer. Leave the lid open for a while, or whenever the washer is idle, to let humidity out.
Code / problem / part / repair
From the code to what you do next.
Frigidaire washer not spinning
On a top-load Frigidaire, the usual cause is an unbalanced load or a lid that isn’t closed. Frigidaire’s tub-not-spinning article says to power off, wait for the lid to unlock, rearrange the clothes and restart. After that it checks load size, shipping materials, level and hose connections.
Washer repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.

