Frigidaire cooktop -- / Mode, not a failure

Frigidaire cooktop
error --

Cooktop / display reference--

A double dash on a knob-control Frigidaire cooktop is not an error. The manual calls it "Cookware not found": the zone is on, but pan detection could not find suitable cookware. Check the pan's material and position, then try again.

Also shown as --

Last reviewed

Cooktop / display reference--
Meaning
A double dash on a knob-control Frigidaire cooktop is not an error. The manual calls it "Cookware not found": the zone is on, but pan detection could not find suitable cookware. Check the pan's material and position, then try again.
Who handles it
Owner checks first, then a technician
Related codes
Source
EN User Manual | Induction Cooktop, A01704805/A

What Frigidaire cooktop -- means.

What it means

A double dash on a knob-control Frigidaire cooktop is not an error. The manual calls it "Cookware not found": the zone is on, but pan detection could not find suitable cookware. Check the pan's material and position, then try again.

What you can safely check

Switch the zone off first so nothing heats while you move the pan.

When to call a technician

The knobs stay dead with -- showing after a reset and a magnet-tested pan.

Your checklist / kept on this device

Safe checks, in order.

0 of 4 checks done
  1. Frigidaire cooktop --: Stainless electric glass cooktop on a granite counter with a saucepan on one element and small lit red characters on the touch control strip at the front edge
    Illustration. Follow your model’s instructions.
    Before you begin

    Turn the knob to OFF

    Switch the zone off first so nothing heats while you move the pan.

  2. Refrigerator door control panel showing a temperature readout beside stainless handles
    Illustration. Follow your model’s instructions.
    Check 2

    Test the pan with a magnet

    The troubleshooting table offers a magnet test: if it clings to the pan's base, the pan is fine for induction.

  3. Technician in a dark jacket seen from behind holding a tablet with an empty checklist, a range in the background.
    Illustration. Follow your model’s instructions.
    Check 3

    Center the pan on its zone

    The same table lists a pan of the wrong size or in the wrong spot as a reason a zone will not respond.

  4. Gloved hands holding multimeter probes on a connector at the open lower back of a refrigerator, tool bag nearby.
    Illustration. Follow your model’s instructions.
    Check 4

    Turn the zone back on

    Push in and turn the knob again. A heat setting should replace the dashes once the pan is detected.

Still showing --?

Tell us the model and what you have already checked, and start the request right here.

Book a visit

Cooktop control.

Conceptual Cooktop sectionTouch panelUser interface boardPower boardWiring1234
  1. 1Touch panel
  2. 2User interface board
  3. 3Power board
  4. 4Wiring

Simplified schematic; real layouts differ by model. Tap an outlined part for its photo and the check that goes with it.

A little more context.

What does -- mean on this cooktop?

The manual lists "- - Cookware not found" as a display message: the zone was set, but pan detection could not find cookware of the correct material on it.

Read the supporting manual

Why does the zone stay cold with dashes showing?

An induction zone heats only under a pan it can sense, so with no pan found the zone holds off. The display tells you why instead of leaving you guessing.

Read the supporting manual

When do dashes point to a repair?

A note in the manual says that if resetting the surface controls does not help and a C, Er or -- message stays while the knobs do nothing, the cooktop needs service.

Read the supporting manual

The manual behind the message.

Manufacturer document

EN User Manual | Induction Cooktop, A01704805/A

Frigidaire / Electrolux

July 2024 / PDF p.6 (4.1 Other display messages)

Manufacturer document

EN User Manual | Induction Cooktop, A01704805/A

Frigidaire / Electrolux

July 2024 / PDF p.7 (note under 4.1)

Source is manual A01704805/A (July 2024) for the knob-operated Professional model. Touch-control cooktops follow another guide.

Here to help

Good questions.
Clear answers.

Talk to our team
Does -- mean the cooktop is broken?

No. The manual lists it as the cookware-not-found message. A pan of the wrong material or one set off-center is the usual match.

Which pans work on induction?

Frigidaire's table gives a quick pan test with a magnet: a pull toward the underside means the metal suits induction.

A good pan still gives dashes. Now what?

Try another pan on a different zone. If every pan gives dashes and the knobs stay dead after a reset, we should look at the cooktop.

How do I reset the surface controls?

For Er, the manual says to set the knob to OFF. For dashes, take the pan off, turn the zone off and start again with a centered pan.

Let’s take care of it.

The range is the heart
of the kitchen. Let’s fix it.