On this page
- Frigidaire says a lower water level than an older washer is normal. 1
- Most models sense the load and add water after the sensing step, which can take a few minutes. 1
- Max Fill adds the most water possible and lengthens the cycle. 2
- Frigidaire does not recommend Max Fill for regular use. 23
- Dry load height should stay below the upper row of holes in the tub. 3
Is it normal for the water not to cover my clothes in a top-load washer?#
Yes. Frigidaire says high-efficiency washers are designed to use less water and energy, and it is normal for the level to look lower than on an older top-load washer. Most models sense the load and decide the water level themselves. 1
This catches people who moved from an older machine with an agitator and a full tub. A low level on its own is the design at work, nothing to worry about. 1
Water also does not arrive at the start. Frigidaire says that water enters once the sensing cycle is complete, which may take a few minutes. So a dry-looking tub right after you press START is not a sign of trouble. 1
Why does my washer wait before adding water?#
Most Frigidaire top-load washers use sensing technology: the washer measures the load first, then adds the amount of water it needs. The sensing step can take a few minutes, and water enters after it finishes. 1
The manual's list of codes shows the same design from another angle. Two of the failures it names are "Load sensing failed" and "Water level sensor failed", and for both the guide says to call service. That is how you know the washer decides the level itself rather than you choosing it. 3
The practical rule is simple. Give the washer a few minutes after START before you decide anything. 1
How full should the tub be in a Frigidaire top-load washer?#
Keep the dry load level no higher than the upper row of holes in the wash tub, and do not overload. Mix large and small items, with large pieces making up no more than half the total wash load. For one heavy item, add one or two towels to balance it. 3
Page 6 of the manual shows this as a drawing: the load stops below the top ring of holes. It is the most useful number you will get from the manual for this topic, because load height decides how much water the sensor asks for. 3
- 1
- 2
- 3
- 4
- 5

Why overloading matters#
The troubleshooting tables in the manual list overloading as a cause of lint, residue on dark items, stiff fabrics and wrinkling. In each case the fix includes reducing the load size or not overloading the washer. A packed tub is a quicker way to a poor wash than a low water level. 3
Why high-efficiency detergent matters#
The manual tells you to use a low-sudsing, high-efficiency detergent to prevent oversudsing, and to look for the high-efficiency symbol on the label. In a washer that uses little water, extra suds are more noticeable than they were in the old one. 3
What is Max Fill and when should I use it?#
Max Fill is a button on some models for loads that need extra water. It adds the maximum amount of water the washer can fill and makes the cycle longer. Frigidaire does not recommend it for regular use, only for special cases. 23
It also is not available with every cycle. The manual lists Max Fill as "certain cycles only", so if the button does nothing on the cycle you picked, that is expected. 23
Here is when it can help, going by what Frigidaire says: loads that really need extra water. The manual does not list examples, so we will not guess at them. For an everyday load, leave it off and let the sensor work. 23
Can I change the cycle after it starts?#
On most models you must press POWER before choosing a new cycle. Turning the selector alone does not change it, and if you try, the lights flash and a signal beeps. The manual says the same for settings and options: press PAUSE, make the new choice and press START again. 34
If you need to add a forgotten item, press PAUSE, wait for the lid lock to release, lift the lid, add it and press START again. The washer continues the current cycle. Do not force a locked lid. 3
What else can make a wash look short of water?#
Several habits make a low level look worse than it is. A tub packed past the upper holes leaves little free water, a heavy single item can sit above the surface, and too much detergent can produce suds that hide what is going on. Fixing the load is easier than blaming the washer. 3
Check the detergent#
The manual asks for a measured amount of detergent, and says the amount depends on the type of detergent, the load size, the soil level and the water hardness. It also says to use a low-sudsing, high-efficiency detergent to prevent oversudsing. Pod-type packs go directly at the bottom of the empty tub before the laundry goes in. 3
Check the lid and the signals#
The washer will not operate with the lid open, so close it before you press START. For your safety the lid is locked during the final spin and unlocks once the cycle ends and the tub has stopped completely. To open it during the final spin, press PAUSE, wait for the lid lock to release, and never force the lid. 3
If the display shows E3 or CL, those are lid codes rather than water-level problems, and the Owner Center has a page for each. Do not mix them up with a fill problem, because the checks are different. 3
Ask what changed#
Did the low level start after a move, a new washer or a new detergent? A new washer explains it, because Frigidaire says the level will look lower than an older top-load model. A sudden change on a washer that used to fill differently is worth a note for the technician, along with the cycle you were using and whether Max Fill was on. 12
What if the washer fills too slowly or not at all?#
If the washer takes too long to fill, it may stop and show E1. The manual says E1 means the washer took more than 30 minutes to fill at low water level, 45 at medium or 60 at high, or that the water level did not change for five minutes. 3
The manual's first checks for a long fill are all owner jobs:
- Close the lid. 3
- Fully open the hot and cold faucets. 3
- Straighten the inlet hoses if they are kinked. 3
- Check water pressure at other outlets in the house. 3
- Clean the inlet screens after disconnecting the hoses. 3
- Look for leaks from the tub. 3
If the situation continues, the manual says to call service. 3 For related questions, see washer not spinning and washer won't start.
For the service itself, see our washer service page.
Sources#
- Top Load Washers - The water level in my Frigidaire Top Load washer does not cover my laundry load. Is this normal? (KB 1848680)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
- Top Load Washers - What is Max Fill and how do I use it on my Frigidaire Top Load washer? (KB 1848679)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text
- All about the Use & Care of your Washer, A29259301 (August 2024)Frigidaire / Electrolux (retailer-hosted copy) · August 2024 · pp. 5-7 (washing procedures, lid lock), p. 9 (Max Fill), p. 16 (overloading), p. 18 (error codes)
- Top Load Washers - How do I use my display or select cycles on my Frigidaire Top Load washer? (KB 1848683)Frigidaire / Owner Center knowledge base · Owner Center article, cached 10.11.2026 (no edition date printed) · Article text


