Before work starts
The technician quotes the work to you at the visit, after looking at the appliance, and nothing is done until you say yes.
Independent appliance repair
Frigidaire gas and electric dryers come to us when they don’t heat, run too long, overheat or won’t start. Tell us the cycle you use and whether the drum turns, then book a technician.


Start with the lint screen and the cycle setting, then the load, humidity and the venting. Frigidaire’s article puts lint screen cleaning after every use first. A clogged duct or hood is the other big one, and a 208-volt circuit lengthens drying by about 20 percent.

Frigidaire’s start checks are the Start button held for two seconds, the cycle knob position, the door, the plug and the breaker. If it starts then stops, the motor may have overheated, or on an electric dryer the thermal limiter may have tripped.

For clothes that come out too dry, Frigidaire says to use Auto Dry instead of Timed Dry and pick a temperature that suits the fabric. A dryer that runs very hot or smells hot is a different problem: the manual lists a clogged lint filter and blocked venting.

If the drum turns but the air stays cold, Frigidaire’s first suspects are the Air Fluff setting and, on an electric dryer, one of its two house fuses or breakers. On a gas dryer, check the gas supply valve and the tank.
We have not researched code meanings for this appliance yet. Use its manual and add a photo of the display to your request.
See the research statusWe don’t list parts for this appliance up front. The technician names any part after the diagnostic and matches it to your exact model before anything is replaced.

We have no illustrated entry for this part yet. Follow the system named in the explanation and the manual cited for your model; a code by itself never tells you what to replace.
Explore the researched partsThree short stages.
Plain, and kept short.

Pick the appliance, describe the problem and add the model number if you have it. The booking form is open 24/7.

The technician checks the range, fridge or washer, explains what failed and quotes the repair before starting.

Parts are fitted, the work is tested, and you see the appliance running before the technician leaves.
Air Fluff or a no-heat setting tumbles without heat.
Frigidaire says clean it after every use and never run the dryer without it.
An electric dryer has two circuit poles. If one trips, the drum may turn with no heat.
A crushed or clogged exhaust duct or blocked hood slows drying. A gas dryer must vent outdoors.
These are the codes on Frigidaire’s dryer manual.
Book a visit if the dryer still won’t heat after the cycle, breaker and vent checks.
Book a visit if the dryer won’t start with the door closed, the cord seated and power on.
Gas dryer: if the gas supply is off or you smell gas, don’t operate the dryer; call your gas supplier.
Leave the heater and the gas parts to the technician.
Arrange a diagnosticThe technician quotes the work to you at the visit, after looking at the appliance, and nothing is done until you say yes.
If Frigidaire’s warranty covers the problem, Frigidaire does that repair. Work we do is covered by our own workmanship warranty.
On an electric dryer a tripped breaker pole can leave the drum turning with no heat. Check the breaker, the cycle and, on a gas dryer, the gas supply. If heat stays off, book a visit.
Frigidaire points to the lint screen, load size, humidity, sensor-bar residue and a blocked vent. Fix those first. If a normal load still runs long, book a technician.
The dryer manual lists C9 as a failed control board, E4 as a failed humidity sensor and E5 as a failed temperature sensor. Book a technician with the code.
If your unit is under Frigidaire’s warranty, Frigidaire handles that repair. Otherwise book with us; the price is agreed before work starts.
Press the start button for two seconds, close the door fully, seat the plug and check the breaker. Don’t use an extension cord. If it still won’t start, book a visit.
Code / problem / part / repair
Start with the lint screen and the cycle setting, then the load, humidity and the venting. Frigidaire’s article puts lint screen cleaning after every use first. A clogged duct or hood is the other big one, and a 208-volt circuit lengthens drying by about 20 percent.
Book a diagnostic for your model, done at your home.
Office addresses and the entry details to have ready.