Start from the symptom
Frigidaire dryer too hot or over-drying.
For clothes that come out too dry, Frigidaire says to use Auto Dry instead of Timed Dry and pick a temperature that suits the fabric. A dryer that runs very hot or smells hot is a different problem: the manual lists a clogged lint filter and blocked venting.

Start with safe observations.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Over-dried clothes
Select the right cycle and temperature, try Auto Dry over a Timed Dry cycle, and follow the care labels on fabrics.
- 2
Lint filter
Clean it before every load. The manual lists a clogged lint filter among causes of an outside that feels too hot or smells hot.
- 3
Exhaust duct and hood
The duct must be 4-inch rigid or semi-rigid metal with no more than four 90-degree bends. Clear any blockage in the duct or outside hood.
- 4
Motor or thermal limiter
If the dryer shuts off after heating, see the won’t-start page: Frigidaire says an overheated motor needs 30 minutes to cool, and a tripped thermal limiter needs service.
- 5
E5 temperature sensor
E5 means the temperature sensor failed. The manual lists only one step: call service.
Systems a technician may investigate.
These parts are linked to the problem. What you noticed does not prove any one of them has failed.

Dryer lint filter
The lint filter catches lint so air can flow through the dryer. Frigidaire says to clean it before or after every load, since a clogged filter makes drying slower and lint is a fire risk. Wash it in warm soapy water now and then to clear the waxy film that fabric softener sheets leave behind.

Dryer exhaust duct and vent hood
The exhaust duct and vent hood carry hot, damp air and lint out of the house. Frigidaire says to inspect and clean the outdoor exhaust about every 18 months, because a clogged duct slows drying. A gas dryer must never run without a duct that vents outdoors.

Dryer thermal limiter
The thermal limiter is a safety switch in an electric Frigidaire dryer. The manual says it turns off the motor in the unlikely event of an overheated situation, and that a service technician must replace it after the cause is corrected.
If the display adds a code.
Keep the exact message.
We have not researched code meanings for this appliance yet. Use its manual and add a photo of the display to your request.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
Stop using the dryer, and book a visit when it smells hot or burnt, if the outside is too hot to touch comfortably after you’ve cleaned the filter and cleared the vent, or if E5 appears. Keep it off until it’s checked.
Arrange a diagnosticSources and model boundaries.
These documents back up the Frigidaire dryer too hot or over-drying advice. Use the manual that matches your model.
- My clothes seem to be over-dried. How can I prevent this? (KB 1853006)
- What should I do if my dryer stops operating? (KB 1853011)
- All about the Use & Care of your Dryer, A29259201
Follow the instructions written for your own model. See how we research these pages.
How do I stop clothes being over-dried?
Frigidaire says to choose the right cycle and temperature, use Auto Dry instead of Timed Dry, and follow fabric care labels.
Why does my dryer smell hot?
The manual lists a clogged lint filter, duct that doesn’t meet its requirements, or a clogged outside hood or duct. Clean the filter and clear the vent; if it continues, book us.
What does E5 mean on a Frigidaire dryer?
The temperature sensor failed. The manual’s only step is to call service, so book a visit.
Is a very hot dryer safe to keep running?
Stop it. Clean the lint filter and check the vent once it has cooled, then book us if the heat or smell comes back.
Code / problem / part / repair
From the code to what you do next.
Frigidaire dryer takes too long to dry
Start with the lint screen and the cycle setting, then the load, humidity and the venting. Frigidaire’s article puts lint screen cleaning after every use first. A clogged duct or hood is the other big one, and a 208-volt circuit lengthens drying by about 20 percent.
Dryer lint filter
The lint filter catches lint so air can flow through the dryer. Frigidaire says to clean it before or after every load, since a clogged filter makes drying slower and lint is a fire risk. Wash it in warm soapy water now and then to clear the waxy film that fabric softener sheets leave behind.
Dryer repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.