Start from the symptom
Frigidaire range surface element not heating.
On an electric range, an element that stays cold or heats unevenly is often down to the control knob, the cookware or the cooktop type. Check you used the right knob, use flat medium to heavy pans, and on a glass top cut the range's power briefly.

Start with safe observations.
Turn the appliance off and unplug it before any owner check. Look out for standing water and sharp debris. Never touch a wet plug or wiring, take off service panels, or go past the owner steps in your manual.
- 1
Use the right knob
The manual lists using the wrong surface control knob for the element needed. Match each knob to its element.
- 2
Check the power level
An element that is not hot enough or too hot may just have the wrong power setting. Adjust the level.
- 3
Switch to better cookware
Use flat, evenly balanced, medium or heavyweight cookware. Frigidaire says lightweight or warped pans heat unevenly and food may burn.
- 4
Coil elements: test the switch
Press the safety switch in the center of the coil. It should spring back. Remove the coil to inspect it, then reseat it or swap it with another burner.
- 5
Glass top: reset
Disconnect the range, wait 30 seconds, then reconnect. No heat on any burner right after installation may be a voltage or wiring issue.
- 6
Keep the glass clean
Residue on the glass ceramic surface can mark it. Use cooktop cleaning creme and a non-abrasive cloth, and keep pan bottoms clean.
More about this symptom.
What causes does the electric range manual give for a cold element?#
The wrong surface control knob for the element, and cookware that is lightweight or warped. If the element runs too hot or too cool, it lists the wrong power setting.
What should I do with a coil burner that is cold?#
Press the safety switch in the middle of the coil to see it spring up. Take the coil out and look for damage. Reinsert it and test, then try it in another burner to separate coil from receptacle.
Can a power problem look like a dead element?#
Yes. If no element heats and the range is new, a voltage or wiring problem is possible. Do not open the range or the outlet yourself. Book a technician.
Systems a technician may investigate.
These parts are linked to the problem. What you noticed does not prove any one of them has failed.

Range surface indicator lights
Frigidaire fits some ranges with a pair of lamps for the cooktop. One, labeled ELEMENT ON, shines while a burner or element is switched on. The other, HOT SURFACE, keeps shining after cooking until the glass has dropped to a moderate temperature. They report heat, not failures.

Control keypad
The keypad is the set of keys or touch pads that tells the control what to do. Frigidaire lists F1 as “Shorted Key Pad” on range ovens, and its dishwasher guide says a shorted keypad drains the unit and flashes its lights. Both guides begin with a power reset.
If the display adds a code.
This topic has no code tied to it.
No other researched code is tied to this topic. Check the exact message in your model manual rather than borrowing another code from the library.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
No element heats on a new install after a reset.
The coil is damaged or the receptacle is burned.
An element works with one pan and not another of the same size.
Only one element is dead after every check.
Arrange a diagnosticSources and model boundaries.
These documents back up the Frigidaire range surface element not heating advice. Use the manual that matches your model.
- User Manual, Electric Range, A30923902
- Ranges - No Heating (KB 1819544)
Follow the instructions written for your own model. See how we research these pages.
Why will only one element on my Frigidaire range heat?
Make sure you turned the knob that belongs to that element. The manual lists using the wrong control knob as a cause. If the knob is correct, swap the coil to another burner, or test the pan on a different element.
Do lightweight pans really matter?
Yes. The manual says lightweight pans heat unevenly and food may burn easily. Frigidaire asks for flat, evenly balanced pans, medium or heavyweight. A warped base also heats unevenly.
How do I reset a glass cooktop range?
Unplug it for 30 seconds, then plug it back in. Frigidaire gives this as the first step when a glass cooktop does not heat. A new range with no heat on any burner may have a voltage or wiring issue.
Is a scratched or discolored cooktop a heating problem?
No. Metallic sheen, scratches and brown specks are surface marks, not heating problems. The manual lists cooktop cleaning creme with a non-abrasive cloth, and a razor-blade scraper for cooked-on soil once the top is cool.
What should a technician hear from me first?
When the knob, power level and pan are right, the reset changes nothing and an element stays cold. A failed element or switch has to be tested with the range powered down.
Code / problem / part / repair
From the code to what you do next.
Frigidaire range will not turn on or does not operate
If the whole range is dead, the manual starts with the cord and the breaker: plug it in firmly, check the fuse or breaker box, and confirm a power outage is not the reason. If only the oven stays off, check the clock and the selected function. On gas models, check the gas regulator.
Control keypad
The keypad is the set of keys or touch pads that tells the control what to do. Frigidaire lists F1 as “Shorted Key Pad” on range ovens, and its dishwasher guide says a shorted keypad drains the unit and flashes its lights. Both guides begin with a power reset.
Range repair
Book a diagnostic for your model, done at your home.
Find your metro
Office addresses and the entry details to have ready.